H
hugow
Splitter Intro Splitter Order
Splitter CSL Units Splitter CS Units
CS-10 Splitter
CS-15 Splitter
The above two units will split a smart card in to either 10 (CS-10) or 15 (CS-15) IRD's (Integrated Receiver Decoder) at a time using one original smart card.
CS-15 operates as doubler if used with two smart cards (2 cards in -> 15 'doubled' cards out), (IR) only.
The below three units will split a smart card in to either 2 (CSL-2), 3 (CSL-3) or 5 (CSL-5) IRD's (Integrated Receiver Decoder) at a time using one original smart card.
CSL-5 Splitter
All the above units will connect to each IRD and share the smart card and allows access to it in a controlled fashion. This is useful for people having a subscription and owning more than one IRD but willing to use all of their IRD's (Integrated Receiver Decoder).
Installing CSL-2, CSL-3 or CSL-5:
Insert the smart card into the combi unit.
Insert combi unit into the IRD.
Installing CS-10 or CS-15:
Place the master unit on the top of an IRD.
Insert a smart card into the master unit (contacts of the smart card are directed to ground). Insert 2nd smart card into 2nd slot for CS-15 to use doubler mode.
Connect a slave unit using the short 6 wire telephone cable on port 0 (first phone connector located nearest to the card slot) at the back of the master unit.
Insert slave unit into the IRD.
Installing remaining Slave Units:
Connect a 4 wire telephone cable with the desired length to a slave unit.
Plug in the other end of the cable into a free port of the master or combi unit.
Insert slave unit into the IRD.
Deinstalling CSL-2, CSL-3 or CSL-5:
Remove slave unit(s) from the IRD and unplug the cable(s).
Remove combi unit from the IRD.
At last remove the smart card from the combi unit.
Deinstalling CS-10 or CS-15:
Remove slave units at every port except port 0 from the IRD's and unplug cables immediately at both ends.
Remove slave unit at port 0 from the IRD and unplug it's short 6 wire cable.
At last remove the smart card(s) from the master unit.
NOTE
Test if your smart card works properly in every IRD before you start with the installation.
Splitter Intro Splitter Order
Splitter CSL Units Splitter CS Units
Bron: http://www.maxking.com/cardsplitter.htm
M.vr.gr.
Hugow
Splitter CSL Units Splitter CS Units
CS-10 Splitter
CS-15 Splitter
The above two units will split a smart card in to either 10 (CS-10) or 15 (CS-15) IRD's (Integrated Receiver Decoder) at a time using one original smart card.
CS-15 operates as doubler if used with two smart cards (2 cards in -> 15 'doubled' cards out), (IR) only.
The below three units will split a smart card in to either 2 (CSL-2), 3 (CSL-3) or 5 (CSL-5) IRD's (Integrated Receiver Decoder) at a time using one original smart card.
CSL-5 Splitter
All the above units will connect to each IRD and share the smart card and allows access to it in a controlled fashion. This is useful for people having a subscription and owning more than one IRD but willing to use all of their IRD's (Integrated Receiver Decoder).
Installing CSL-2, CSL-3 or CSL-5:
Insert the smart card into the combi unit.
Insert combi unit into the IRD.
Installing CS-10 or CS-15:
Place the master unit on the top of an IRD.
Insert a smart card into the master unit (contacts of the smart card are directed to ground). Insert 2nd smart card into 2nd slot for CS-15 to use doubler mode.
Connect a slave unit using the short 6 wire telephone cable on port 0 (first phone connector located nearest to the card slot) at the back of the master unit.
Insert slave unit into the IRD.
Installing remaining Slave Units:
Connect a 4 wire telephone cable with the desired length to a slave unit.
Plug in the other end of the cable into a free port of the master or combi unit.
Insert slave unit into the IRD.
Deinstalling CSL-2, CSL-3 or CSL-5:
Remove slave unit(s) from the IRD and unplug the cable(s).
Remove combi unit from the IRD.
At last remove the smart card from the combi unit.
Deinstalling CS-10 or CS-15:
Remove slave units at every port except port 0 from the IRD's and unplug cables immediately at both ends.
Remove slave unit at port 0 from the IRD and unplug it's short 6 wire cable.
At last remove the smart card(s) from the master unit.
NOTE
Test if your smart card works properly in every IRD before you start with the installation.
Splitter Intro Splitter Order
Splitter CSL Units Splitter CS Units
Bron: http://www.maxking.com/cardsplitter.htm
M.vr.gr.
Hugow
